Objective To evaluate the biomechanical stability of a newly-designed Y type pedicle screw (YPS) in osteoporotic synthetic bone. Methods The osteoporotic synthetic bone were randomly divided into 3 groups (n=20). A pilot hole, 3.0 mm in diameter and 30.0 mm in deep, was prepared in these bones with the same method. The YPS, expansive pedicle screw (EPS), and bone cement-injectable cannulated pedicle screw (CICPS) were inserted into these synthetic bone through the pilot hole prepared. X-ray film examination was performed after 12 hours; the biomechanical stability of YPS, EPS, and CICPS groups was tested by the universal testing machine (E10000). The test items included the maximum axial pullout force, the maximum running torque, and the maximum periodical anti-bending. Results X-ray examination showed that in YPS group, the main screw and the core pin were wrapped around the polyurethane material, the core pin was formed from the lower 1/3 of the main screw and formed an angle of 15° with the main screw, and the lowest point of the inserted middle core pin was positioned at the same level with the main screw; in EPS group, the tip of EPS expanded markedly and formed a claw-like structure; in CICPS group, the bone cement was mainly distributed in the front of the screw and was dispersed in the trabecular bone to form a stable screw-bone cement-trabecular complex. The maximum axial pullout force of YPS, EPS, and CICPS groups was (98.43±8.26), (77.41±11.41), and (186.43±23.23) N, respectively; the maximum running torque was (1.42±0.33), (0.96±0.37), and (2.27±0.39) N/m, respectively; and the maximum periodical anti-bending was (67.49±3.02), (66.03±2.88), and (143.48±4.73) N, respectively. The above indexes in CICPS group were significantly higher than those in YPS group and EPS group (P<0.05); the maximum axial pullout force and the maximum running torque in YPS group were significantly higher than those in EPS group (P<0.05), but there was no significant difference in the maximum periodical anti-bending between YPS group and EPS group (P>0.05). Conclusion Compared with EPS, YPS can effectively enhance the maximum axial pullout force and maximum rotation force in the module, which provides a new idea for the design of screws and the choice of different fixation methods under the condition of osteoporosis.
Objective To investigate the effect of anteromedial coronoid facet fracture and lateral collateral ligament complex (LCLC) injury on the posteromedial rotational stability of the elbow joint. Methods The double elbows were obtained from 4 fresh adult male cadaveric specimens. Complete elbow joint (group A,n=8), simple LCLC injury (group B,n=4), simple anteromedial coronoid facet fracture (group C,n=4), and LCLC injury combined with anteromedial coronoid facet fracture (group D,n=8). The torque value was calculated according to the load-displacement curve. Results There was no complete dislocation of the elbow during the experiment. The torque values of groups A, B, C, and D were (10.286±0.166), (5.775±0.124), (6.566±0.139), and (3.004±0.063) N·m respectively, showing significant differences between groups (P<0.05). Conclusion Simple LCLC injury, simple anteromedial coronoid facet fracture, and combined both injury will affect the posteromedial rotational stability of the elbow.
Objective To design customized titanium alloy lunate prosthesis, construct three-dimensional finite element model of wrist joint before and after replacement by finite element analysis, and observe the biomechanical changes of wrist joint after replacement, providing biomechanical basis for clinical application of prosthesis. Methods One fresh frozen human forearm was collected, and the maximum range of motions in flexion, extension, ulnar deviation, and radialis deviation tested by cortex motion capture system were 48.42°, 38.04°, 35.68°, and 26.41°, respectively. The wrist joint data was obtained by CT scan and imported into Mimics21.0 software and Magics21.0 software to construct a wrist joint three-dimensional model and design customized titanium alloy lunate prosthesis. Then Geomagic Studio 2017 software and Solidworks 2017 software were used to construct the three-dimensional finite element models of a normal wrist joint (normal model) and a wrist joint with lunate prosthesis after replacement (replacement model). The stress distribution and deformation of the wrist joint before and after replacement were analyzed for flexion at and 15°, 30°, 48.42°, extension at 15°, 30°, and 38.04°, ulnar deviation at 10°, 20°, and 35.68°, and radial deviation at 5°, 15°, and 26.41° by the ANSYS 17.0 finite element analysis software. And the stress distribution of lunate bone and lunate prosthesis were also observed. Results The three-dimensional finite element models of wrist joint before and after replacement were successfully constructed. At different range of motion of flexion, extension, ulnar deviation, and radial deviation, there were some differences in the number of nodes and units in the grid models. In the four directions of flexion, extension, ulnar deviation, and radial deviation, the maximum deformation of wrist joint in normal model and replacement model occurred in the radial side, and the values increased gradually with the increase of the range of motion. The maximum stress of the wrist joint increased gradually with the increase of the range of motion, and at maximum range of motion, the stress was concentrated on the proximal radius, showing an overall trend of moving from the radial wrist to the proximal radius. The maximum stress of normal lunate bone increased gradually with the increase of range of motion in different directions, and the stress position also changed. The maximum stress of lunate prosthesis was concentrated on the ulnar side of the prosthesis, which increased gradually with the increase of the range of motion in flexion, and decreased gradually with the increase of the range of motion in extension, ulnar deviation, and radialis deviation. The stress on prosthesis increased significantly when compared with that on normal lunate bone. Conclusion The customized titanium alloy lunate prosthesis does not change the wrist joint load transfer mode, which provided data support for the clinical application of the prosthesis.
ObjectiveTo understand risk factors of abdominal aortic aneurysm (AAA) rupture and the latest progress.MethodThe domestic and foreign related literatures on risk factors affecting AAA rupture were retrieved and reviewed.ResultsBesides some definite risk factors of AAA rupture, including age, gender, hypertension, smoking, family history, complications (such as diabetes mellitus, hypertension, dyslipidemia, etc.), the biomechanical factor was the crucial factor of AAA rupture, including the aortic compliance, aortic wall peak value of pressure, aortic wall calcification, and hemodynamics. The latest imaging methods such as the high resolution ultrasound, function and molecular imaging, and phase contrast magnetic resonance imaging could provide technical supports for the prediction of AAA rupture.ConclusionsThere are many risk factors affecting AAA rupture. Clinicians might prevent and make individualize treatment for AAA rupture according to its risk factors, and risks of AAA rupture could be more accurately assessed with help of new medical imaging examination.
ObjectiveTo compare the strength difference between the interfacial screw and the interfacial screw combined with bone tunnel crossing technology to fix the tibial end of ligament during anterior cruciate ligament (ACL) reconstruction through the biomechanical test.MethodsTwenty fresh frozen pig tibia were randomly divided into two groups (n=10) to prepare ACL reconstruction models. The graft tendons in the experimental group were fixed with interfacial screw combined with bone tunnel crossing technology, and the graft tendons in the control group were fixed with interfacial screw. The two groups of specimens were fixed in the high-frequency dynamic mechanics test system M-3000, and the length change (displacement), ultimate load, and stiffness of graft tendons were measured through the reciprocating test and load-failure test.ResultsThe results of reciprocating test showed that the displacement of the experimental group was (3.06±0.58) mm, and that of the control group was (2.82±0.46) mm, and there was no significant difference between the two groups (t=0.641, P=0.529). The load-failure test results showed that the stiffness of the experimental group and the control group were (95.39±13.63) and (91.38±14.28) N/mm, respectively, with no significant difference (t=1.021, P=0.321). The ultimate load of the experimental group was (743.15±173.96) N, which was significantly higher than that of the control group (574.70±74.43) N (t=2.648, P=0.016).ConclusionIn ACL reconstruction, the fixation strength of tibial end with interface screw combined with bone tunnel crossing technology is obviously better than that of interface screw alone.
Objective To investigate the effect of Navio robot-assisted unicompartmental knee arthroplasty (UKA) on the biomechanics of knee joint during sitting-up movement, and to determine whether UKA can maintain the biomechanical characteristics of knee joint. Methods The clinical data of 8 patients with medial compartment osteoarthritis treated with medial fixed platform of Navio robot-assisted UKA between January 2018 and January 2019 and had the complete follow-up data were retrospectively analyzed. There were 4 males and 4 females; the age ranged from 58 to 67 years, with an average of 62.3 years. The disease duration was 6-18 months, with an average of 13 months. The varus deformity ranged from 4° to 6°, with an average of 5°; the knee flexion range of motion was 0°-130°, with an average of 110°. All patients had no extension limitation. The imaging data of bilateral knees during sitting-up movement were collected by biplane C-arm X-ray machine at 3 weeks before operation and 7 months after operation. The three-dimensional models of femur and tibia were established by dual-energy CT scanning, and the three-dimensional models of femur and tibia were matched and synchronized with the femur and tibia in X-ray film by automatic matching tracer software. The biomechanical parameters of femur and tibia were measured, including internal rotation/external rotation, varus/valgus, forward/backward displacement of medial and lateral tibia contact center, and lateral compartment joint space. Results Eight patients were followed up 5-7 months, with an average of 6.4 months. In the comparison of the affected side before and after operation, except for the difference of varus/valgus which was significant (t=4.959, P=0.002), the differences in other indicators was not significant (P>0.05). There were significant differences in varus/valgus and internal rotation/external rotation between healthy and affected sides at 3 weeks before operation (P<0.05), and the differences in other indicators was not significant (P>0.05). At 7 months after operation, the difference in the forward and backward displacement of medial tibia contact center was significant (t=3.798, P=0.007), and the differences in other indicators was not significant (P>0.05). Conclusion UKA can effectively correct the varus and valgus of the knee joint, and restore the rotational biomechanical characteristics of the affected knee joint. It does not affect the establishment of the lateral compartment joint space, but the medial and lateral tibia contact center still changes.
The phenomenon of sex differences exists in patients who have abdominal aortic aneurysms (AAA). The occurrence rate of AAA is higher in male, while the rates of rupture and postoperative mortality are higher for female. This phenomenon of sex differences would affect the diagnosis, treatment and postoperative rehabilitation for AAA patients. This article reviewed the recent research status of sex differences on AAA, and explored the phenomenon of sex differences from the aspects of threshold determination, biomechanics and mechanobiology. This review points out that the sex differences on AAA could ascribe to the differences of biomechanical environment and biological properties induced by the vascular size, anatomy structure and structure components of abdominal aortic artery. The comprehensive investigations of the sex differences on AAA could help to optimize the diagnosis, treatment and device design, patient care and rehabilitation strategy of AAA based on sex differences phenomenon.
ObjectiveTo compare the biomechanical characteristics of self-made nickel-titanium shape memory alloy stepped plate with calcaneal plate and cannulated compression screws in fixing calcaneal osteotomy.MethodsCalcaneal osteotomy was operated on 6 fresh-frozen lower limbs collected from donors. Then three kinds of fixation materials were applied in random, including the self-made nickel-titanium shape memory alloy stepped plate (group A), calcaneal plate (group B), and cannulated compression screws (group C). Immediately after fixation, axial loading of 20-600 N and 20 N/s in speed was introduced to record the biomechanical data including maximum displacement, elastic displacement, and maximum load. Then fatigue test was performed (5 Hz in frequency and repeat 3 000 times) and the same axial loading was introduced to collect the biomechanical data. Finally, the axial compression stiffness before and after fatigue test were calculated.ResultsThere was no significant difference in the axial compression stiffness between pre- and post-fatigue test in each group (P>0.05). However, the axial compression stiffness was significant higher in group A than that in groups B and C both before and after fatigue test (P<0.05). No significant difference was found between group B and group C (P>0.05).ConclusionSelf-made nickel-titanium shape memory alloy stepped plate is better than calcaneal plate and cannulated compression screws in axial load stiffness after being used to fix calcaneal osteotomy.
ObjectiveTo explore the nature of micromovement and the biomechanical staging of fracture healing.MethodsThrough literature review and theoretical analysis, the difference in micromovement research was taken as the breakthrough point to try to provide a new understanding of the role of micromovement and the mechanical working mode in the process of fracture healing.ResultsThe process of fracture healing is the process of callus generation and connection. The micromovement is the key to start the growth of callus, and the total amount of callus should be matched with the size of the fracture space. The strain at the fracture end is the key to determine the callus connection. The strain that can be tolerated by different tissues in the fracture healing process will limit the micromovement. According to this, the fracture healing process can be divided into the initiation period, perfusion period, contradiction period, connection period, and physiological period, i.e., the biomechanical staging of fracture healing.ConclusionBiomechanical staging of fracture healing incorporates important mechanical parameters affecting fracture healing and introduces the concepts of time and space, which helps to understand the role of biomechanics, and its significance needs further clinical test and exploration.
ObjectiveTo observe the changes in the biomechanical properties of the cornea of diabetic retinopathy (DR), and analyze its relationship with the degree of DR. MethodsA retrospective study. From September 2020 to February 2021, 83 patients with type 2 diabetes (T2DM) combined with DR treated in the Department of Ophthalmology, The First Affiliated Hospital of Zhengzhou University, 83 eyes (DR group), 30 patients with T2DM without DR recruited from the outpatient clinic 30 eyes (NDR group) and 30 eyes of non-diabetes patients (NDM group) were included in the study. All left eyes were chose as the study eye. Among the 83 eyes in the DR group, 39 eyes were non-proliferative DR (NPDR) and 44 eyes were proliferative DR (PDR). Based on this, they were divided into NPDR group and PDR group. There was no statistically significant difference in age (t=1.10) and sex ratio (χ2=0.46) among patients in the DR group, NDR group, and NDM group (P>0.05); body mass index (t=3.74), glycosylated hemoglobin (t=35.02) and the length of the eye axis (t=5.51), the difference was statistically significant (P<0.05). The eye response analyzer (ORA) was used to measure the corneal hysteresis (CH), corneal resistance factor (CRF), Goldman related intraocular pressure (IOPg), and corneal compensatory intraocular pressure (IOPcc). The corneal topography was used to measure the central corneal thickness (CCT) of the examined eye. The differences of CCT, IOPcc, IOPg, CH, CRF among multiple groups were compared by one-way analysis of variance. Multiple linear regression was used to analyze the relationship between CH, CRF and related influencing factors in DR patients. ResultsThere were statistically significant differences in CCT, IOPcc, IOPg, CH, and CRF among the eyes of the DR group, NDR group, and NDM group (F=3.71, 5.60, 9.72, 9.02, 21.97; P<0.05). Pairwise comparisons were between groups, CH, CRF: the difference between the DR group and the NDM group and the NDR group was statistically significant (P<0.05); CCT: the difference between the DR group and the NDM group was statistically significant (P<0.05), and The difference in the NDR group was not statistically significant (P>0.05). CCT, CH, CRF: the difference between the NDR group and the NDM group was not statistically significant (P>0.05). The results of multiple linear regression analysis showed that CCT and IOPcc in DR patients were independent influencing factors of CH [CCT: β=0.01, 95% confidence interval (CI) 0.01-0.03, P=0.013; IOPcc: β=－0.15, 95%CI －0.25-－0.05, P=0.005]; Age, CCT, IOPcc were independent influencing factors of CRF [Age: β=－0.06, 95%CI －0.09-－0.03, P＜0.001; CCT: β=0.01, 95%CI 0.00-0.02, P=0.049; IOPcc: β=0.16, 95%CI 0.07-0.25, P=0.001]. The comparison of CCT, CH, CRF, adjusted CH, and adjusted CRF of the eyes in the NDR group, NPDR group, and PDR group were statistically significant (F=3.76, 5.36, 12.61, 6.59, 10.41; P<0.05). Pairwise comparison between groups, CH, CRF, adjusted CH, adjusted CRF: the difference between the NPDR group, the PDR group and the NDR group was statistically significant (P<0.05), and the difference between the PDR group and the NPDR group was not statistically significant (P>0.05); CCT: The difference between NPDR group and NDR group, PDR group and NPDR group was not statistically significant (P>0.05), and the difference between PDR group and NDR group was statistically significant (P<0.05). ConclusionThe CH and CRF of eyes with T2DM and DR are elevated; CCT and IOPcc are independent influencing factors of CH, and age, CCT and IOPcc are independent influencing factors of CRF.